| 1 |
The Effects of the Thermo-Mechanical Process Variables on the Microstructure, Mechanical Properties, and Recrystallization Behavior of the Commercially Pure Titanium
|
Iranian Journal of Materials Forming
|
| 2 |
75Cr3C2-25NiCr and 86WC-10Co-4Cr High Wear- and Corrosion-Resistant Cermet Coatings Deposited on A356 Substrate by High-Velocity Oxy-Fuel Technique
|
Coatings
|
| 3 |
Electrode lifetime in resistance spot welding of coated sheets: Experiments and modeling
|
Materials Today Communications
|
| 4 |
Reinforced Cu sheets with accumulative roll bonding process in assisting nanostructured composite of low and high boron contents; Effects of morphology and composition of reinforcement
|
Materials Today Communications
|
| 5 |
Correlation between nanoindentation response and wear characteristics of CrN-based coatings deposited by Arc-PVD method
|
International Journal of Applied Ceramic Technology
|
| 6 |
Mechanical properties and tribological performance of A356/Cr3C2-NiCr surface composite developed by high-velocity oxy-fuel and post friction stir processing treatment
|
Surfaces and Interfaces
|
| 7 |
Improving the fracture toughness of multi-layered commercial pure aluminum via warm accumulative roll bonding
|
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
|
| 8 |
High Strength-Elongation Balance in Warm Accumulative Roll Bonded AA1050 Sheets
|
METALS AND MATERIALS INTERNATIONAL
|
| 9 |
Improving mechanical and tribological performances of pure copper matrix surface composites reinforced by Ti2AlC MAX phase and MoS2 nanoparticles
|
MATERIALS CHEMISTRY AND PHYSICS
|
| 10 |
The Effects of Age Hardening on Tribological Behavior of Lightweight Fe-Mn-Al-C Steel
|
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
|
| 11 |
Control on nanostructured quaternary Ti–Al–O–B composite synthesized via electrospinning method, from nanoparticles to nanowhiskers
|
JOURNAL OF SOL-GEL SCIENCE AND TECHNOLOGY
|
| 12 |
Substantial electrode life enhancement in resistance spot welding of galvanised steels through nanolayered multi-layer CrN/(Cr,Al)N coating
|
SURFACE ENGINEERING
|
| 13 |
On the Simultaneous Improving of Strength and Elongation in Dual Phase Steels via Cold Rolling
|
Metals
|
| 14 |
Effect of FSP Pass Number on the Tribological Behavior of AZ31 Magnesium Alloy
|
Journal of Stress Analysis
|
| 15 |
Kinetics of Austenite Recrystallization during the Annealing of Cold-rolled Fe-Mn-Al-C Steel
|
Iranian Journal of Materials Forming
|
| 16 |
Prediction of the failure mode of automotive steels resistance spot welds
|
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING
|
| 17 |
Criterion for predicting expulsion in resistance spot welding of steel sheets
|
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
|
| 18 |
Mechanism of TiC formation in laser surface treatment of the commercial pure titanium pre-coated by carbon using PVD process
|
JOURNAL OF ALLOYS AND COMPOUNDS
|
| 19 |
A new approach to synthesis Ti2AlC MAX phase using PVD coating and post-laser treatment
|
SURFACE & COATINGS TECHNOLOGY
|
| 20 |
Tribological behavior of AZ31/ZrO2 surface nanocomposites developed by friction stir processing
|
TRIBOLOGY INTERNATIONAL
|
| 21 |
Production and investigation of mechanical properties and electrical resistivity of cement‑matrix nanocomposites with graphene oxide and carbon nanotube reinforcements
|
Archives of Civil and Mechanical Engineering
|
| 22 |
Effect of mono and hybrid ceramic reinforcement particles on the tribological behavior of the AZ31 matrix surface composites developed by friction stir processing
|
CERAMICS INTERNATIONAL
|
| 23 |
Effect of Friction Stir Processing on the Microhardness, Wear and Corrosion Behavior of Al6061 and Al6061/SiO2 Nanocomposites
|
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
|
| 24 |
Development of Cu-TiO2 surface nanocomposite by friction stir processing: Effect of pass number on microstructure, mechanical properties, tribological and corrosion behavior
|
JOURNAL OF ALLOYS AND COMPOUNDS
|
| 25 |
Correlation of ferrite and martensite micromechanical behavior with mechanical properties of ultrafine grained dual phase steels
|
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
|
| 26 |
High strength-elongation balance in ultrafine grained ferrite-martensite dual phase steels developed by thermomechanical processing
|
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
|
| 27 |
On the surface reinforcing of A356 aluminum alloy by nanolayered Ti3AlC2 MAX phase via friction stir processing
|
SURFACE & COATINGS TECHNOLOGY
|
| 28 |
Development of A356/Al2O3 + SiO2 surface hybrid nanocomposite by friction stir processing
|
SURFACE & COATINGS TECHNOLOGY
|
| 29 |
Microstructural evolution and mechanical properties of ultrafine grained AA2024 processed by accumulative roll bonding
|
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
|
| 30 |
Strengthening mechanisms of nano-grained commercial pure titanium processed by accumulative roll bonding
|
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
|
| 31 |
Electrochemical Behavior Assessment of Microand Nano-Grained Commercial Pure Titanium in H2SO4 Solutions
|
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
|
| 32 |
Simultaneous Investigation of the Effect of Advanced Thermomechanical Treatment and Repetitive Cyclic Voltammetry on the Electrochemical Behavior of AISI 430 Ferritic Stainless Steel
|
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
|
| 33 |
The effect of Nb on texture evolutions of the ultrafine-grained dual-phase steels fabricated by cold rolling and intercritical annealing
|
JOURNAL OF ALLOYS AND COMPOUNDS
|
| 34 |
Effect of immersion time on the passive and electrochemical response of annealed and nano-grained commercial pure titanium in Ringer's physiological solution at 37 °C
|
Materials Science and Engineering: C
|
| 35 |
An Investigation of mechanical properties in accumulative roll bonded nano-grained pure titanium
|
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
|
| 36 |
Resistance Spot Welding of Steels: Modeling and Simulation
|
International Journal of Iron & Steel Society of Iran (IJISSI)
|
| 37 |
On the study of tensile and strain hardening behavior of a thermomechanically treated ferritic stainless steel
|
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
|
| 38 |
Microstructural evolution, mechanical properties ,and strain hardening behavior of ultrafine grained commercial pure copper during the accumulative roll bonding process
|
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
|
| 39 |
Strengthening Mechanisms and Electrochemical Behavior of Ultrafine- Grained Commercial Pure Copper Fabricated by Accumulative Roll Bonding
|
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
|
| 40 |
Effect of grain refinement on mechanical and electrochemical properties of ultra-fine grained AA1050 fabricated via ARB process
|
Journal of Manufacturing Processes
|
| 41 |
Electrochemical Behavior of Pure Copper in Phosphate Buffer Solutions: A Comparison Between Micro- and Nano-Grained Copper
|
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
|
| 42 |
Microstructure, mechanical properties and electrochemical behavior of AA1050 processed by accumulative roll bonding (ARB)
|
JOURNAL OF ALLOYS AND COMPOUNDS
|
| 43 |
The influence of cyclic voltammetry passivation on the electrochemical behavior of fine and coarse-grained AISI 430 ferritic stainless steel in an alkaline solution
|
JOURNAL OF ALLOYS AND COMPOUNDS
|
| 44 |
Effects of grain size and dislocation density on strain hardening behavior of ultrafine grained AA1050 processed by accumulative roll bonding
|
JOURNAL OF ALLOYS AND COMPOUNDS
|
| 45 |
Electrochemical Behavior of Passive Films Formed on the Surface of Coarse-, Fine- and Ultra-fine-Grained AA1050 Based on a Modified PDM
|
Acta Metallurgica Sinica-English Letters
|
| 46 |
Correlation of microstructure and strain hardening behavior in the ultrafine-grained Nb-bearing dual phase steels
|
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
|
| 47 |
Development of a high strength and ductile Nb-bearing dual phase steel by cold-rolling and intercritical annealing of the ferrite- martensite microstructures
|
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
|
| 48 |
Kinetics of Ferrite Recrystallization and Austenite Formation During Intercritical Annealing of the Cold- Rolled Ferrite/Martensite Duplex Structures
|
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
|
| 49 |
Effect of Nb on Microstructures and Mechanical Properties of an Ultrafine- Grained Dual Phase Steel
|
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
|
| 50 |
Nanoindentation study of ferrite-martensite dual phase steels developed by a new thermomechanical processing
|
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
|
| 51 |
Microstructures, Mechanical Properties, and Strain Hardening Behavior of an Ultrahigh Strength Dual Phase Steel Developed by Intercritical Annealing of Cold-Rolled Ferrite/Martensite
|
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
|
| 52 |
Correlation of Mechanical Properties with Fracture Surface Features in a Newly Developed Dual-Phase Steel
|
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
|
| 53 |
Strengthening Mechanisms of Ultrafine Grained Dual Phase Steels Developed by New Thermomechanical Processing
|
ISIJ INTERNATIONAL
|
| 54 |
Development of a New Ultrafine/Nano Ferrite-Carbide Microstructure by Thermomechanical Processing
|
Acta Metallurgica Sinica-English Letters
|
| 55 |
Tribological Behavior of A356/Al2O3 Surface Nanocomposite Prepared by Friction Stir Processing
|
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
|
| 56 |
Development of Al356eAl2O3 Nanocomposite Coatings by High Velocity Oxy-fuel Technique
|
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
|
| 57 |
A novel technique for development of A356/Al2O3 surface nanocomposite by friction stir processing
|
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
|
| 58 |
A novel route for development of ultrahigh strength dual phase steels
|
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
|
| 59 |
Effects of initial microstructure and thermomechanical processing parameters on microstructures and mechanical properties of ultrafine grained dual phase steels
|
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
|